स्टकमा उपलब्ध लोकप्रिय उत्पादन

HC-HS 2-D7-EBUS

HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert

$35.46USD

326 स्टकमा

मुख्य विशिष्टताहरू

:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.

प्रकारहरू:D7

परीक्षणहरू:DIN VDE 0627/86

चौडाइ:21 mm

आपूर्तिकर्ता जानकारी

उत्पादहरू: 0

सामान्यतया २-३ कार्यदिवसभित्र पठाइन्छ

गुणस्तर ग्यारेन्टी

छिटो शिपिङ

प्राविधिक सहयोग

प्राविधिक विशिष्टताहरू

प्यारामीटर	मूल्य
	Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
प्रकारहरू	D7
परीक्षणहरू	DIN VDE 0627/86
चौडाइ	21 mm
उचाइ	34.8 mm
लम्बाइ	21 mm
शृङ्खला	HC-HS
सामान्य जानकारी	for HC-D7 housing, axial connection 2.0 mm, Allen key
आवेदन	Power
उत्पादनको प्रकार	Contact insert with a fixed no. of positions
विधानसभा नोट	To ensure correct use, installation in housing with IP54 protection or better is required
मूल्याङ्कन गरिएको वर्तमान	40 A
लेख संशोधन	04
सम्पर्क व्यास	4 mm
सम्पर्क सामग्री	Copper alloy
षट्कोणीय सकेट	SW2,0
सम्पर्क नम्बरिङ	1 - 2
टर्क कस्दै	0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing)
जडान प्रोफाइल	2+PE
प्रदूषणको डिग्री	3
आयामी रेखाचित्र
पदहरूको संख्या	2
मूल्याङ्कन गरिएको वृद्धि भोल्टेज	6 kV
ओभरभोल्टेज श्रेणी	III
जडान प्रविधि	Axial screw connection
सम्पर्क सामग्रीको प्रकार	turned
पावर सम्पर्कहरूको संख्या	2
मूल्याङ्कन गरिएको भोल्टेज (III/3)	400 V
कन्डक्टर क्रस सेक्सन	4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used)
सम्पर्क वाहक सामग्री	PC
सम्पर्क सतह सामग्री	Ag
सम्मिलन/निकासी चक्रहरू	≥ 500
जडान क्रस सेक्सन AWG	10 ... 8
परिवेशको तापक्रम (सञ्चालन)	-40 °C ... 125 °C (including heating up of contacts)
मानक अनुसार जडान	IEC / EN
निर्माण र परीक्षण नियमहरू	DIN VDE 0627/86
UL ९४ अनुसार ज्वलनशीलता मूल्याङ्कन	V0
व्यक्तिगत तारको स्ट्रिपिङ लम्बाइ	8 mm +1 mm